February 11 14 Key West to Marathon and Three Lay Days There 42 4 Miles

We took in our dock lines at 7:30 and were anchored in Marathon at 3:30, sailing all but the first five and last fifteen minutes of outing and ining. The winds were forecast from the north at ten knots which meant no big waves, because they have to build up from south of the Keys. The wind did come from there eventually, and nicely, with a steady fifteen knots; we were making near eight knots at the end.
We had full sails up throughout, but the early part of the passage was troubling. The wind had too much of an easterly component so we were close hauled on port tack and I was envisioning the point where we would have to tack to avoid the shoals at the south side of Hawk Channel. And relative wind varied frequently by 25 degrees and between eight and fifteen knots requiring very frequent trimming of sails and course changes to get what speed we could make out of the wind and avoid the tack if possible. But no tack was needed in the end.
We were passed by s/v Liberty, which had been docked near us in the Key West Bight Marina. I hailed her to thank her for passing us on the gentlemanly leeward side. We avoided motoring, though it meant some 2.5 knot stretches. I find that once I switch on the "iron genoa" to assist us, it stays on far too long, its noise degrading the pleasure.
We communicated with s/v Autumn Born and they were arriving in Marathon too, but from the east. We saw them anchored outside the harbor to the west of the island, where it was rolly, and AB weighs twice ILENE. AB is in the safest possible place: with lots of room around her to let out 100 feet of chain in ten feet of water, as compared to the small crowded but more protected anchorage area inside. We dropped three times before we found the right spot, and have 60 feet of snubbed chain out in 12 feet of water. Good holding, tested by winds over 20 knots the third night.
In the channel we passed s/v Liberty again, somewhat stuck in the sand south of the channel. I said I would come out by dink to help once we were anchored but she broke herself free less than a minute later and followed us in. We were hailed by the crew of s/v Saint Somewhere, who we had tried to help up in Titusville, and later by Dean and Susan of Autumn Born, who were dinking in to register and get on the waiting list for a mooring. The winds have been so constantly from the north that people waiting for a window to hop over to the Bahamas are still waiting and not leaving.
Dean and Susan stopped by for wine and cheese on their way back to their boat. I love talking with Dean and save up my questions for him because he is so knowledgeable. I was pleased to able to give back a bit by showing him our experiences in the Marquesas Keys and Boca Grande Key. They will be going to Key West soon to meet family, and plan to take a mooring up in rolly Garrison Bight.We did not go to shore to register until the next day because that first night we had no need for anything the shore had to offer, and we also saved one nights dinghy docking fee, almost $18. The waiting list for a mooring is now longer than when we were here last month so there was no need to go ashore to get ourselves on the list because we will be leaving before anything becomes available. We had the last of our paella, watched Downton Abbey and called it a night.
We had a dinner with Dean and Susan and two other couples at Burdines, a very casual restaurant above the fuel dock the next night. Ilene invited herself and me and they had a table for eight.
Next morning I cleared all the "stuff" from the aft cabin to our bed in the forward one to provide space for work. I topped up the seven batteries with distilled water and prepared for the arrival of Alex
The line above Alexs head is how we keep the door
of our aft head, the cats head, open and stable, so it does not
flail and break itself from its hinges as the boat moves.
who installed and tested the "combiner" which will charge the starting battery automatically, whenever we are making electricity, but disconnect it from the house bank whenever we are not.
During the 9:00 am net on Channel 68 we announced our arrival and so did Tex and Maria of m/v "Heaven Sent", their 46 foot Grand Banks trawler on which they live. They belong to the Harlem and the Huguenot YCs, Tex is a Past Commodore of the Harlem. I later asked if anyone could lend me a set of feeler gauges to check the alignment of the flexible coupling that I had to install and Justin, of s/v "Selkey", from Cork, Ireland, responded and brought the tool over later and explained to me how to use it. Lene went ashore and did some shopping in the supermarket, while I set to work on the flexible coupling.

It is an ingenious device, attached by four forward facing bolts to the flange at the aft end of the transmission, and attached by four more bolts facing aft to the flange at the forward end of the propeller shaft.
It has two metal bars, one visible in the photo, that will hold it together if it shatters, so the shaft wont slide out of the hole in the boat through which the shaft rotates if the coupling shatters. But its purpose is to shatter if you hit something hard. By shattering it is supposed to prevent your transmission from shattering.
The first thing I noticed was that the new bolts installed in the old coupling by Deatons Yard in North Carolina were smaller in diameter than those that came with the new sealed unit from the factory. This is not good.
Well at least the spacing of the holes from each other through the flanges matched the spacing of those holes in the new unit. Hooray! And the new larger diameter bolts fit through the holes in the flanges. Hooray!  But this means that since North Carolina, we have been motoring with smaller diameter bolts in larger diameter holes, which is never a good thing and may have been the cause of the vibration, or contributed to it. But the new bolts were fractionally longer than the old ones so that when I got them installed they rubbed against the transmission housing. This was very bad; its just not going to work. What to do? Washers on the bolt head aft end of those bolts would place them far enough away I thought, so I took the whole thing apart again. But the washers were larger in diameter than the nuts, preventing my wrench from gripping the nuts to tighten them. What to do? Alex was doing his thing for us and suggested that I could bring my 17mm wrench in to his shop next morning and grind down the sides of the wrench, and narrow them so it would fit. But during the night I thought of two alternative solutions: (1) use smaller diameter washers, or (2) grind down the ends of the four bolts. Time for another consultation with Dean. Grinding the bolts was selected and Alexs electric grindstone made quick work of it. I put it all together again for the third time (it does not permit the removal of parts without complete dis-assembly, because there is just not enough room to get the bolts out). Having tested with the feeler gauge, it looked right and we turned on the engine and put it in gear, briefly. Im hoping the problem is solved. Time will tell when we use the engine to propel us for real.

One evening, we dinked over to Heaven Sent, (sorry for the fuzzy piture of this beautiful roomy boat). It was
 a long 1.5 mile dinghy ride, to the far eastern end of the harbor where Heaven Sent is tied up to the seawall.


The adjacent boat was s/v Liberty, which, we learned, is being single handed by a lady from St. Augustine.
I have known Tex and Maria since 1990 when I joined the Harlem. We had some wine before walking to a local restaurant, Dockside Tropical Cafe, one of several here that has live music. But every table was filled except one picnic table outside -- close enough to hear but not see the music. We ordered but later cancelled the order because the wait would have been at least an hour and it was cold out. Back at Heaven Sent, Maria cooked up a very fine dinner and we did not get back to ILENE until after ten pm, late for us.
Next day was a Family Fun Fest at the adjacent City Park. Lene had volunteered us to help the kids make projects with materials and tools donated by Home Depot, but when we got there they had too many volunteers and we were released. A wide variety of things for kids to do.
Our final dinner was at Lazy Days, just past Burdines, the nicest restaurant we visited in Marathon. Valentines Day, hence a rose for every lady. We had the pleasure of introducing Tex and Maria from our Club to Dean and Susan and Earl and Cathy, of s/v Seeker, who we had been introduced to by Dean and Susan in St. Augustine. Maybe Dean and Susan were starting to think that we had no friends other than those they introduced us to.
Susan, Kathy, Earl, Lene, Me, Maria and Tex (Photo credit to Dean)

Related Posts by Categories

0 comments:

Post a Comment




Blog Archive

Powered by Blogger.